Відео

Brilliant idea

Thank you

Believe it or not… I love punts…..basically a work boat . Great for just muddling around , fishing , being flat bottomed and being appealing to me…..there’s just something about punts !!

Three times the same video ????

You have cut out the unnecessary steps. I’m going to use your method.

Immer dran denke, es gibt keine Milchfinger, die wachsen nicht wieder nach 🤭

I wish you success! Boat building can be very exciting. I'm building the sixth! ua-cam.com/video/VSyKXQZtn9Q/v-deo.html

I'm building my first boat now and I chose a flat bottom dory because the fairing of the frame and Chinese is pretty straight forward. My next boat will be a little more difficult. Building a boat has really changed my outlook of woodworking, I have gained patience moving one step at a time. And bending wood to my will is quite invigorating.

I suspect a power planer would save time.

I just got fiberglass on the roof. See "Building a Houseboat Glassing Cabin Roof"

Klaus very fine work👍🏻 I wonder how you would finish this roof? Fibreglass or calico?

Danke!

Mit Sicherheit interessant. Leider verdeckst du deine Arbeit mit der linken Hand

Stitch and glue method is a very strong when used with thickened epoxy resin. Nice boat!

The little boy will build on that experience and pleasure all his life I'm sure. Happy days!

Very funny!

Classic boat! Lots of curves. Great windows and port holes. You must be very proud! Congratulations from a fellow boat builder.

why would you not just ply it?

Freut mich, dass Dir mein Clip was gebracht hat. Wie kommt man auf solche Dinge? Durch Beschäftigung mit Vektoralgebra und analytischer Geometrie. Damit fängt übrigens auch jede Offset-Tabelle eines Bootes an, die nichts anderes ist als eine Menge von Bezugspunkten oder auch Koordinaten im Raum.

Bald fange ich meine Ausbildung als Bootsbauer an! Umso mehr ich im voraus schon weiss umso besser!

Yep, another dry bond glass job

Very cool ! I want to build one !

More about the construction: Unzip and open with index.html. drive.google.com/file/d/1daWUnrl0BXCNI_7a7zN1FHs6CvMV-dA7/view?usp=sharing

Das Boot ist sehr gut

KEep It Simple StupidI am a genius at being being stupid, so simple, the best I've seen

thanks! a really smart trick!

In checking the Dow Chemical spec sheet for Styrofoam it gives the following parameters. TABLE 2: Physical Properties of STYROFOAMTM Brand SM Extruded Polystyrene Foam Insulation (1) Vertical compressive strength is measured at 10 percent deformation or at yield, whichever occurs rst. (2) Basedon1”(25mm)thickness. Property And Test Method Value Thermal R esistance per inch (25 mm), ASTM C518 @ 75°F (24 ̊C) mean temp., ft2•h• ̊F/Btu (m2• ̊C/W) min., R -value (RSI) 5.0 (.88) Compressive Strength(1), ASTM D1621, psi (kPa), min. 30 (207) Water Absorption, ASTM D2842, % by volume, max. 0.7 Water Absorption, ASTM C272, % by volume, max 0.3 Water Vapour Permeance, ASTM E96, perm (ng/Pa•s•m2), max.(2) 1.5 (90) Maximum Use Temperature, ̊F ( ̊C) 165 (74) Coef cient of Linear Thermal Expansion, ASTM D696, in/in• ̊F (mm/m• ̊C) 3.5 x 10-5 (6.3 x 10-2) Note the maximum Use Temperature.

Great work!!!

I am sI check a lot of woodworking handbooks. These one from woodprix are the best.

Fantastic and very smart! Thanks for share!

Note: The shape of the frames is more or less curved, especially in the anterior region

"Bevel's Angel and Frames' Rounding is given by itself" This sentence makes no sense. But the method shown is sound and well demonstrated in the video.

Iron water pipe? Maybe you mean galvanized pipe?

Thanks for the video. I was considering making one exactly like this (but using thinner foam that I already have). I wasn't sure if it would handle the heat properly without melting and warping like PVC does. Since your application works well, I'm going to give my idea a try.

If I am making a boat with a "pad" to help it get on plane quicker would I then fair the pad as opposed to the frame itself?

Nice Job guys!!!

Are there any plans to this houseboat available?

Beautiful.

I was waiting for this video. Nice to see her finished

now i know,where my G clamp went

Die gezeigte Methode hätte mir bei den von mir in meiner Jugend gebauten Doppelknickspantern geholfen. Allerdings habe ich nach dem ersten Boot in den 70ern einen der damals neuen Elektrohobel gekauft und es dann mehr nach Gefühl hingehobelt. Die Hobelmesserschleiferei auf dem Stein war mir zu aufwendig. Hat auch funktioniert, musste ja auch, da der Leim damals kaum fugenfüllend war. Irgendso ein Resorcinharz mit Pulver ergab eine kochfeste Verleimung nach AW100. Schönes Vide0 - danke dafür!

Super! Danach habe ich lange gesucht! Wird direkt umgesetzt.

Look forward to next video. Please some inside layout pictures.

How is the boat coming, haven't seen an up date.

Something else You write that you used the side of the level. I presume your level has a U profile. Similarly, one can use a corresponding aluminum profile. Homemade for me was cheaper and faster.

Thank you for your comment. For my demonstration, I used an older free boat plan. Google "Svenson free boat plans dolphin"! The Body Plan on 0.3 jpg so can not be built! In this special case, the outlines of the frames at the bottom were nowhere straight. Really! The outline of a frame is only straight when rabbit and chine are parallel on this station. My intention was to make fairing easier and more precise and effektive. But it's best to try this on a model.

Here's my take on it. By adding shims to the frames, you have changed the design of the Naval Architect. The only surface that needs to be developed is the bow where the bottom goes from flat to a cylinder. It probably didn't make much difference but the boat would be marginally more tender and the extra pieces may become a maintenance issue. You have a good technique for the bow section though, I just do them with the side of a level.

The launch is planned for next year. If you want to learn more, send me an email to klaus.silbernagl at hk.mailbox.de

Did you finish this boat?

Great Job.